-
در بخش Sell Offers، دسته بندی Glue، Province Ilam موردی پیدا نشد.
دسته بندی Glue را امتحان کنید.-
Cold Laminate Adhesive, Rolling and Wrapping PVC, U PVC Adhesive.
***Supplier of cold press rolling or wrapping PVC adhesive (Product code: TPAN-04205) for on-line/off-line production lines, a replacement for expensive hot melt or hot glue*** Usage: Used in cold press rolling and wrapping production lines for laminating plastic on: foam sheets, marble sheets, profiles made from UPVC, WPC, PVC, and Polywood materials in on-line or off-line extrusion production lines, replacing hot melt or hot glue. -Key Features: 1- Suitable for cold press rolling, wrapping, or flat pressing of PVC products (replacement for hot melt adhesive) 2- Ability to bond patterned PVC laminate, High Gloss, Super Matte coatings, and natural wood (thin/thick) on surfaces made of UPVC, WPC, PVC, and Polywood, 3- Over 50% economic savings in energy consumption and cold adhesive purchase compared to hot melt or hot glue (both in cost per kilogram and coverage of at least 25 square meters of PVC coating surface for covering 8 marble sheets, foam sheets, or 14 UPVC Thermowall profiles) per kilogram of TPAN-04205 cold PVC laminate adhesive. 4- Reduction of waste and high startup speed of laminate press production lines. ### - Technical specifications and instructions for using cold rolling/wrapping PVC adhesive, TPAN-0465 Data sheet: [TPAN-0465 datasheet link](https://www.jooyeshgar.com/articles/det-2145). * TPAN-04205 and TPAN-0465B are among the most standard industrial adhesives for cold press rolling and wrapping PVC laminate on polymeric and composite foamed PVC, UPVC, wood-plastic, and polywood panel surfaces. Also, due to transparency *(no yellowing)* and hardness higher than glass *(high impact resistance underlayer for glossy and thin laminates)* and high adhesion *(fusion or welded adhesion to plastic surfaces (PVC, UPVC) processed with cold PVC adhesive)*, they are among the most standard one-component air-dry adhesives in advanced global PVC laminate pressing industries.* ## ***- Features of PVC rolling adhesive, TPAN-0465 & TPAN-04250:*** 1. No gelation of adhesive during in-place operation of the adhesive applicator system **(no gel time).** 2. No graininess, swelling, or orange peel effect on the coating surface after pressing **(anti-swelling against direct and indirect heat).** 3. No corrosion or excessive softening of glued surfaces after pressing **(non-corrosive).** 4. Suitable time gap between adhesive applicator and rolling press unit about 4-60 seconds **(appropriate working time).** 5. UV resistant and no yellowing on light-colored coatings such as white, due to high transparency and colorlessness of the adhesive product **(resistant to adhesive degradation under harsh environmental conditions and UV).** 6. Less need to adjust adhesive processing amount by the machine operator when changing coating thickness **(wide application range with low consumption weight).** 7. No need for thinner during use, with the possibility of piping adhesive onto the rolling press applicator roller and washable with quick thinner and most organic solvents **(long-term storability).** 8. The technical team and machinery unit of Diako Choob Baspar Faravard are ready to transfer production knowledge, machinery, and expert technical service for setup, optimization, and adhesive type replacement (hot to cold) of rolling/wrapping press production lines nationwide **(full-time support).** 9. The most standard adhesive to replace expensive foreign hot melt adhesives in domestic production lines. On-line adhesive - On-line adhesive - On-line adhesive, On-line adhesive - Hot melt adhesive replacement - Hot melt adhesive replacement - PVC on-line adhesive - Cold acrylic rolling press polywood adhesive (100% guaranteed) - Cold acrylic rolling press polywood adhesive - Grade 1 cold acrylic adhesive waterproof and peel-resistant - Cold rolling press polywood door adhesive - Cold rolling press polywood door adhesive - Polywood rolling adhesive - Polywood rolling adhesive - Polywood rolling press adhesive - Polywood rolling press adhesive - Polywood door rolling press adhesive - PVC laminate adhesive - UPVC wrapping adhesive - PVC laminate adhesive - PVC laminate adhesive - Glass adhesives - Glass adhesives - Glass adhesives - Embossed coating adhesive - Embossed coating adhesive - Embossed coating adhesive - Acrylic laminate adhesive - Acrylic laminate adhesive - Acrylic laminate adhesive - Rolling press adhesive – Rolling press adhesive - Rolling press adhesive - PVC adhesive - PVC adhesive - PVC adhesive - Special adhesive for glass sheet production - Special adhesive for glass sheet production - Special adhesive for glass sheet production - Cold acrylic laminate adhesive - Cold acrylic laminate adhesive - Cold acrylic laminate adhesive - Cold acrylic laminate adhesive - Cold acrylic laminate adhesive - Cold acrylic laminate adhesive - PVC coating adhesive - PVC coating adhesive - PVC coating adhesive - PVC wrapping adhesive - Wrapping press adhesive - UPVC and polywood profile wrapping adhesive - Polywood wrapping adhesive - Polywood wrapping adhesive - Polywood wrapping adhesive - Special cold wrapping adhesive - Cold acrylic wrapping adhesive - Cold acrylic wrapping adhesive - Cold foamed PVC wrapping adhesive - Cold wood-plastic profile wrapping adhesive - Cold UPVC door and window wrapping adhesive. Cold UPVC profile laminate wrapping adhesive. Marble sheet adhesive. Marble sheet adhesive, marble sheet adhesive solvent-based adhesive specially for bonding PVC coating on hard UPVC sheet substrate. Marble sheet rolling adhesive. Marble sheet rolling adhesive - Marble sheet rolling adhesive. Marble sheet laminate adhesive. Marble sheet laminate adhesive - PVC rolling and wrapping press adhesive - PVC rolling and wrapping press adhesive - Cold rolling and wrapping PVC adhesive - Rolling and wrapping PVC adhesive - Cold rolling and wrapping PVC adhesive - Cold rolling and wrapping PVC adhesive.
Glue Alborz -
Devcon Plastic-Steel Putty A
DEVCON A\r\nDecon A adhesive is one of the industrial products of the Irish DEVCON company. Welding is used. This epoxy is easily attached to all kinds of materials and is resistant to oil, fuel, water and many chemicals. This product can be used for inexpensive repair of parts and surfaces including pipes. used bearings, machines, etc.\r\nDEVCON A steel epoxy putty is suitable for filling, restoring and gluing metal surfaces and for use as metal welding in areas where welding is not possible.\r\n\r\nDucon A is resistant to chemicals, alcohol, solvents and acids.\r\n\r\nThis product is gray in color and can be machined after drying. degrees Celsius.\r\n\r\nThis DEVCON product can be connected to various materials such as iron, steel, concrete and aluminum.\r\n\r\nThis DEVCON product can be used for repairing equipment, parts and Various surfaces, including pipes, bearings, machines, etc., are used at a very low cost.\r\n\r\nThe problems created in the casting of industrial parts can be corrected by Dokan A.
Glue Esfahan -
5cm print adhesive tape
Azar Adhesive Company has been able to meet customer satisfaction and needs by producing printed adhesives in different widths We can do print on the adhesive bar in the least possible number for you. The minimum printable number of adhesive tape is 60 rings. The company has also been able to produce a simple adhesive tape for different thicknesses for different uses using advanced devices. You can visit azarchasb.ir or contact 09360648395 or 04133432531.
Glue East Azarbaijan -
Opolak 6100 similar to Belzona 1111
Opolak 6100 is a two-component adhesive for repairing and renovating all kinds of machines and equipment. This glue is similar to Belzona 1111 glue, which is based on resins\r\nEpoxy is made with high molecular weight and reinforced with silicon steel, so that it can be easily machined after the glue is fully cured. also\r\nIt can be used as a high strength structural adhesive for gluing all kinds of metal parts to create load bearing shims or to repair them.\r\nUses\r\n✓ Repairing shafts and hydraulic jacks\r\n✓ Repair of parietal tubes\r\n✓ Repairing the shell of industrial equipment and seats and thorn holders\r\n✓ Repair of metal pipes and tanks\r\n✓ Repair of engine shell and parts\r\n✓ Repairing the surface of metal flanges\r\nSpecification\r\n✓ Excellent wear resistance\r\n✓ Appropriate temperature and chemical resistance\r\n✓ Electrical insulation\r\n✓ High strength\r\nHow to use\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue. Before mixing the glue, clean the desired surfaces and free from dust and grease. Suitable solvents such as acetone can be used to degrease surfaces. direction\r\nThe oxidized surface of metal surfaces should be removed to reveal a white and clean metal surface. For other materials, the old surface must be removed somehow during the process\r\nSanding, grinding or sandblasting to create a rough and new surface. Also, the painted surfaces must be completely free of paint.\r\nIn the parts where there are cracks with dimensions of 70 to 100 mm, it is necessary to stabilize the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts to which the glue does not need to stick with paper tape or with separating wax, then mix the entire amount of resin and hardener from two cans of both components until the color of the glue is completely uniform. At temperatures below 10 degrees Celsius\r\nEasy to mix glue, bring the temperature to 20 to 25 degrees Celsius and then mix the two components. ) if smaller amounts of glue are required\r\nUse the table above (and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.\r\nIn order to achieve the best result and the highest adhesive adhesion to surfaces, consider the following:\r\n✓ Do not use glue in temperatures below 5 degrees Celsius and humidity of 90% and in the presence of fog, steam, snow and rain. At the time of use, the application surface must be completely dry\r\n✓ Use glue in contaminated places with the possibility of oil and grease contamination due to the operation of nearby devices or contaminated with oil vapors and cigarette smoke.\r\n\r\nMixing percentage by weight\r\n5 parts resin component\r\n1 part Hardener component
Glue Khorasan Razavi -
Opolak 6500 similar to Belzona 1311
Opolak 6500 is a two-component adhesive for renovating all kinds of metals damaged by abrasion corrosion. This adhesive is similar to Belzona 1311, which is based on high molecular weight epoxy resins reinforced with silicon steel and ceramic particles with high wear resistance, and the adhesive formulation is designed to act as a corrosion and wear resistant coating. be used It can also be used as a high strength structural adhesive for gluing all kinds of metal parts to create load-bearing shims or to repair them.\r\n\r\n**Uses**\r\n Repair of all types of pumps\r\n Repair of butterfly and gate valves\r\n Repair of elbow and tee joints\r\n Repair of heat exchangers and its components including tube sheets\r\n Restoration of butterflies\r\n\r\n**Specification**\r\nExcellent wear resistance\r\n Suitable temperature and chemical resistance\r\n Electrical insulation\r\n High strength\r\n\r\n**how to use**\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue.\r\nBefore mixing the glue, clean the desired surfaces and free from dust and grease. For metal surfaces, the oxidized surface must be removed\r\nuntil the white and clean surface of the metal appears. For other materials, the old surface must be removed in some way during the sanding, grinding or sand-blasting process to create a rough and new surface. Also, the painted surfaces must be completely free of paint.\r\nIn the parts where there are cracks with dimensions of 70 to 100 mm, it is necessary to stabilize the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts that do not need to be glued with paper tape or with separating wax.\r\n\r\n**mixing percentage by weight**\r\n5 parts resin component\r\n1 part Hardener component\r\nThen mix the entire amount of resin and hardener from two cans of both components completely until the color of the glue is completely uniform. At a temperature less than 10 degrees Celsius, bring the glue to a temperature of 20 to 25 degrees Celsius and then mix the two components. (If smaller amounts of glue are needed, use the table above) and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.\r\nIn order to achieve the best result and the highest adhesive adhesion to surfaces, consider the following:\r\n Do not use glue in temperatures below 5 degrees Celsius and humidity of 90% and in the presence of fog, steam, snow and rain. At the time of use, the application surface must be completely dry\r\n Use glue in contaminated places with the possibility of contamination with oil and grease caused by the operation of nearby devices or contaminated with oil vapors and cigarette smoke.
Glue Khorasan Razavi -
Adhesive 123 400 ml
The 123 -profile adhesive, whose industrial name is cyanocrylate, or instant adhesive or versatile adhesive usually has a fatty or accelerator spray that is used before the liquid and increases the adhesion speed. The spray makes the glue glue faster to the desired surface. 400 ml weight Application of Plastic Industries - Medical Industries - Zebali Industries - Construction, Home, Metal, Wooden Industries Submitting quickly to all parts of the country Contact us to purchase and install polyurethane boards and find out the price of a board polyurethane insulation Engineer Chavoshi 09199644020 09022454984 Polyurethane Board Insulation Al -Zal al -Lahurah Fast communication through our Instagram: _instagram.com/kara_energy Website: https://www.karaaa.com/ Website: kara
Glue Tehran -
Opolac 2100 similar to Araldite 2011
Opolak 2100 is a two-component, environmental curing adhesive with high strength and good toughness. This glue can be used to glue all kinds of metals, rubber, ceramics, thermoset plastics. It is a versatile adhesive for various industries. This adhesive can be used in chemical environments with medium temperature and corrosiveness.\r\nUses\r\n Pipe connection and GRE, GRP and GRVE composite connections\r\n Repair of metal pipelines\r\n Repair of composite pipelines\r\n Bonding of various parts in water and sewage, petrochemical and oil and gas industries\r\nSpecification\r\n Multipurpose\r\n Low shrinkage\r\n Good chemical resistance\r\n Environmental baking\r\n Temperature tolerance of 80 degrees Celsius\r\nHow to use\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue.\r\nBefore mixing the glue, clean the desired surfaces and free from dust and grease.\r\nFor metal surfaces, the oxidized surface must be removed to expose the white and clean surface of the metal. For other materials, the old surface must be removed in some way during the sanding or grinding process until a rough and new surface is created. Also, painted surfaces must be completely free of paint.\r\n\r\nMixing percentage\r\n100 grams = 2100 / A\r\n50 grams = 2100 / B\r\n\r\nThen mix component A and component B completely with the proportions given in the table above and apply a thin film of it on both surfaces that you want to glue together. The highest shear strength is achieved in glue with a thickness of 0.5 to 1 mm. Keep the desired surfaces fixed and motionless until the glue is cured.
Glue Khorasan Razavi -
Oplock 6100L similar to Devcon Grade A
Opolak 6100 is a two-component adhesive for repairing and renovating all kinds of machines and equipment. This glue is similar to Belzona 1111 glue, which is based on resins\r\nEpoxy is made with high molecular weight and reinforced with silicon-containing steel, so that it can be easily machined after the glue is fully cured. also\r\nIt can be used as a high strength structural adhesive for gluing all kinds of metal parts (to create a load-bearing shim) or to repair them.\r\n\r\n**Uses**\r\n✓ Repair of shafts and hydraulic jack\r\n✓ Repair of parietal tubes\r\n✓ Repairing the shell of industrial equipment and seats and thorn holders\r\n✓ Repair of metal pipes and tanks\r\n✓ Repair of engine shell and parts\r\n✓ Repairing the surface of metal flanges\r\n\r\n**Specification**\r\n✓ Excellent wear resistance\r\n✓ Appropriate temperature and chemical resistance\r\n✓ Electrical insulation\r\n✓ High strength\r\n\r\n**how to use**\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue. Before mixing the glue, clean the desired surfaces and free from dust and grease. Suitable solvents such as acetone can be used to degrease surfaces. direction\r\nThe oxidized surface of metal surfaces should be removed to reveal a white and clean metal surface. For other materials, the old surface must be removed somehow during the process\r\nSanding, grinding or sandblasting (to create a rough and fresh surface. Also, the painted surfaces must be completely free of paint.\r\nIt is necessary in the parts where there are cracks with dimensions of 70 to 100 mm\r\nFix the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts that do not need to be glued with paper tape or with separating wax.\r\n\r\n**mixing percentage by weight**\r\n5 parts resin component\r\n1 part Hardener component\r\nThen, mix the total amount of resin and hardener from two cans of both components completely so that the color of the glue is completely uniform. At a temperature below 10 degrees Celsius, bring the glue to a temperature of 20 to 25 degrees Celsius and then mix the two components. (If smaller amounts of glue are needed, use the table above) and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.
Glue Khorasan Razavi
Similar Products
-
