Victor Raines glue

Opolak 6100 is a two-component adhesive for repairing and renovating all kinds of machines and equipment. This glue is similar to Belzona 1111 glue, which is based on resins\r\nEpoxy is made with high molecular weight and reinforced with silicon-containing steel, so that it can be easily machined after the glue is fully cured. also\r\nIt can be used as a high strength structural adhesive for gluing all kinds of metal parts (to create a load-bearing shim) or to repair them.\r\n\r\n**Uses**\r\n✓ Repair of shafts and hydraulic jack\r\n✓ Repair of parietal tubes\r\n✓ Repairing the shell of industrial equipment and seats and thorn holders\r\n✓ Repair of metal pipes and tanks\r\n✓ Repair of engine shell and parts\r\n✓ Repairing the surface of metal flanges\r\n\r\n**Specification**\r\n✓ Excellent wear resistance\r\n✓ Appropriate temperature and chemical resistance\r\n✓ Electrical insulation\r\n✓ High strength\r\n\r\n**how to use**\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue. Before mixing the glue, clean the desired surfaces and free from dust and grease. Suitable solvents such as acetone can be used to degrease surfaces. direction\r\nThe oxidized surface of metal surfaces should be removed to reveal a white and clean metal surface. For other materials, the old surface must be removed somehow during the process\r\nSanding, grinding or sandblasting (to create a rough and fresh surface. Also, the painted surfaces must be completely free of paint.\r\nIt is necessary in the parts where there are cracks with dimensions of 70 to 100 mm\r\nFix the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts that do not need to be glued with paper tape or with separating wax.\r\n\r\n**mixing percentage by weight**\r\n5 parts resin component\r\n1 part Hardener component\r\nThen, mix the total amount of resin and hardener from two cans of both components completely so that the color of the glue is completely uniform. At a temperature below 10 degrees Celsius, bring the glue to a temperature of 20 to 25 degrees Celsius and then mix the two components. (If smaller amounts of glue are needed, use the table above) and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.

Opolak 6500 is a two-component adhesive for renovating all kinds of metals damaged by abrasion corrosion. This adhesive is similar to Belzona 1311, which is based on high molecular weight epoxy resins reinforced with silicon steel and ceramic particles with high wear resistance, and the adhesive formulation is designed to act as a corrosion and wear resistant coating. be used It can also be used as a high strength structural adhesive for gluing all kinds of metal parts to create load-bearing shims or to repair them.\r\n\r\n**Uses**\r\n Repair of all types of pumps\r\n Repair of butterfly and gate valves\r\n Repair of elbow and tee joints\r\n Repair of heat exchangers and its components including tube sheets\r\n Restoration of butterflies\r\n\r\n**Specification**\r\nExcellent wear resistance\r\n Suitable temperature and chemical resistance\r\n Electrical insulation\r\n High strength\r\n\r\n**how to use**\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue.\r\nBefore mixing the glue, clean the desired surfaces and free from dust and grease. For metal surfaces, the oxidized surface must be removed\r\nuntil the white and clean surface of the metal appears. For other materials, the old surface must be removed in some way during the sanding, grinding or sand-blasting process to create a rough and new surface. Also, the painted surfaces must be completely free of paint.\r\nIn the parts where there are cracks with dimensions of 70 to 100 mm, it is necessary to stabilize the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts that do not need to be glued with paper tape or with separating wax.\r\n\r\n**mixing percentage by weight**\r\n5 parts resin component\r\n1 part Hardener component\r\nThen mix the entire amount of resin and hardener from two cans of both components completely until the color of the glue is completely uniform. At a temperature less than 10 degrees Celsius, bring the glue to a temperature of 20 to 25 degrees Celsius and then mix the two components. (If smaller amounts of glue are needed, use the table above) and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.\r\nIn order to achieve the best result and the highest adhesive adhesion to surfaces, consider the following:\r\n Do not use glue in temperatures below 5 degrees Celsius and humidity of 90% and in the presence of fog, steam, snow and rain. At the time of use, the application surface must be completely dry\r\n Use glue in contaminated places with the possibility of contamination with oil and grease caused by the operation of nearby devices or contaminated with oil vapors and cigarette smoke.

Opolak 2200 is a two-component, heat-curing adhesive with excellent chemical resistance and temperature tolerance. This glue can be used for gluing all kinds of metals, ceramics,\r\nused thermoset plastics. It is an adhesive for the harsh working conditions of the oil, gas and petrochemical industries. This adhesive in chemical environments with temperature and\r\nHigh corrosion can be used. The excellent chemical resistance of Epolak series 2200 glue against acids and bases with medium to high concentration is the reason for the high use of this glue.\r\nIt has been used in most chemical industries, petrochemicals, oil and gas industries, power plants, etc.\r\n\r\n**Uses**\r\n✓ GRE, GRP and GRVE composite pipes and fittings\r\n✓ Repair of metal pipelines\r\n✓ Repair of composite pipelines\r\n✓ Bonding all kinds of parts in the water and sewage, petrochemical and other industries\r\nOil and Gas\r\n\r\n**Specification**\r\n✓ Temperature resistance with la\r\n✓ Low shrinkage\r\n✓ High chemical resistance\r\n✓ Temperature cooking\r\n✓ Ability to withstand temperatures up to 150 degrees Celsius\r\n\r\n**how to use**\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue. Before mixing the glue, clean the desired surfaces and free from dust and grease\r\nFor metal surfaces, the oxidized surface must be removed to expose the white and clean surface of the metal. For other materials, the old surface must be removed in some way during the sanding or grinding process to create a rough and new surface. Also, the painted surfaces must be completely free of paint.\r\n\r\n**Percentage of disorder**\r\n100 grams = 2200 / A\r\n24 grams = 2200 / B\r\n\r\nThen mix component A and component B completely with the proportions given in the table above and apply a thin film of it on both surfaces that you want to glue together. The highest shear strength is achieved in glue with a thickness of 0.5 to 1 mm. Keep the desired surfaces fixed and motionless until the glue is cured.

Opolak 2100 is a two-component, environmental curing adhesive with high strength and good toughness. This glue can be used to glue all kinds of metals, rubber, ceramics, thermoset plastics. It is a versatile adhesive for various industries. This adhesive can be used in chemical environments with medium temperature and corrosiveness.\r\nUses\r\n Pipe connection and GRE, GRP and GRVE composite connections\r\n Repair of metal pipelines\r\n Repair of composite pipelines\r\n Bonding of various parts in water and sewage, petrochemical and oil and gas industries\r\nSpecification\r\n Multipurpose\r\n Low shrinkage\r\n Good chemical resistance\r\n Environmental baking\r\n Temperature tolerance of 80 degrees Celsius\r\nHow to use\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue.\r\nBefore mixing the glue, clean the desired surfaces and free from dust and grease.\r\nFor metal surfaces, the oxidized surface must be removed to expose the white and clean surface of the metal. For other materials, the old surface must be removed in some way during the sanding or grinding process until a rough and new surface is created. Also, painted surfaces must be completely free of paint.\r\n\r\nMixing percentage\r\n100 grams = 2100 / A\r\n50 grams = 2100 / B\r\n\r\nThen mix component A and component B completely with the proportions given in the table above and apply a thin film of it on both surfaces that you want to glue together. The highest shear strength is achieved in glue with a thickness of 0.5 to 1 mm. Keep the desired surfaces fixed and motionless until the glue is cured.

Opolak 6100 is a two-component adhesive for repairing and renovating all kinds of machines and equipment. This glue is similar to Belzona 1111 glue, which is based on resins\r\nEpoxy is made with high molecular weight and reinforced with silicon steel, so that it can be easily machined after the glue is fully cured. also\r\nIt can be used as a high strength structural adhesive for gluing all kinds of metal parts to create load bearing shims or to repair them.\r\nUses\r\n✓ Repairing shafts and hydraulic jacks\r\n✓ Repair of parietal tubes\r\n✓ Repairing the shell of industrial equipment and seats and thorn holders\r\n✓ Repair of metal pipes and tanks\r\n✓ Repair of engine shell and parts\r\n✓ Repairing the surface of metal flanges\r\nSpecification\r\n✓ Excellent wear resistance\r\n✓ Appropriate temperature and chemical resistance\r\n✓ Electrical insulation\r\n✓ High strength\r\nHow to use\r\nThe amount of strength obtained from the glue and its durability during the working life depends on the level of preparation of the desired surfaces before applying the glue. Before mixing the glue, clean the desired surfaces and free from dust and grease. Suitable solvents such as acetone can be used to degrease surfaces. direction\r\nThe oxidized surface of metal surfaces should be removed to reveal a white and clean metal surface. For other materials, the old surface must be removed somehow during the process\r\nSanding, grinding or sandblasting to create a rough and new surface. Also, the painted surfaces must be completely free of paint.\r\nIn the parts where there are cracks with dimensions of 70 to 100 mm, it is necessary to stabilize the cracks by drilling and screwing. Remove small cracks by sanding and clean and prepare the surface again. Cover the parts to which the glue does not need to stick with paper tape or with separating wax, then mix the entire amount of resin and hardener from two cans of both components until the color of the glue is completely uniform. At temperatures below 10 degrees Celsius\r\nEasy to mix glue, bring the temperature to 20 to 25 degrees Celsius and then mix the two components. ) if smaller amounts of glue are required\r\nUse the table above (and apply with a spatula on both the surfaces you want to glue together or the surface you want to cover.\r\nPress the glue completely on the surface so that all the cracks and pores of the surface are filled with glue. If used to glue two surfaces, keep the desired surfaces fixed and motionless until the glue is cured.\r\nIn order to achieve the best result and the highest adhesive adhesion to surfaces, consider the following:\r\n✓ Do not use glue in temperatures below 5 degrees Celsius and humidity of 90% and in the presence of fog, steam, snow and rain. At the time of use, the application surface must be completely dry\r\n✓ Use glue in contaminated places with the possibility of oil and grease contamination due to the operation of nearby devices or contaminated with oil vapors and cigarette smoke.\r\n\r\nMixing percentage by weight\r\n5 parts resin component\r\n1 part Hardener component

Profab 123 glue, whose industrial name is cyanoacrylate, or instant glue or universal glue, usually has a greasy spray or accelerator with it, which is used before the liquid and increases the speed of adhesion. The spray makes the glue stick to the desired surface faster.\r\n400 ml weight\r\nApplication of plastic industries - medical industries - plastic industries - construction, household, metal, wooden industries\r\n\r\nFast delivery to all parts of the country\r\nContact us to buy and install polyurethane board insulation and to know the price of polyurethane board insulation\r\nEngineer Chavoshi\r\n09199644020\r\n09022454984\r\n\r\nPolyurethane board insulation\r\nAl-Azl Al-Loh Bliurtan\r\n\r\nFast communication through our Instagram:\r\n_instagram.com/kara_energy\r\nwebsite :\r\nhttps://www.karaaa.com/\r\n\r\nsite :\r\nKara

Butyl sealant adhesive, Vitec tape V-tech VT-160S Vital Tape butyl Sealant |\r\nButyl sealant adhesive, Vitec tape V-tech VT-160S Vital Tape butyl Sealant |\r\nButyl sealant adhesive, Vitec tape V-tech VT-160S Vital Tape butyl Sealant |\r\nThese polymers or living glue (butyl tape) can be used in multi-pane glass. It is also used for automotive purposes.\r\nThese polymers or living glue (butyl tape) can be used in multi-pane glass. It is also used for automotive purposes.\r\nThese polymers or living glue (butyl tape) can be used in multi-pane glass. It is also used for automotive purposes.\r\n\r\nDimensions\r\n457 x 0.95 x 0.95 cm

V-tech VT-183 Vital Shellac\r\nShellac washer adhesive V-tech VT-183 Vital Shellac |\r\nMade in: Malaysia\r\nVolume: 59ml\r\nResistance: against petroleum products\r\nApplication: repair and sealing\r\nUsage: 1) For use in automotive and mechanical industries\r\nSherlock gasket adhesive (shellac) for use in automotive and mechanical industries, to repair and seal cardboard, metal felt and rubber cylinder head gaskets. Prevents leakage in threaded connections, easy to use due to having a brush and resistant to most petroleum products.\r\nSherlock gasket adhesive (shellac) for use in automotive and mechanical industries, to repair and seal cardboard, metal felt and rubber cylinder head gaskets. Prevents leakage in threaded connections, easy to use due to having a brush and resistant to most petroleum products.